FAQ

How the calculators work out their results, and what they assume.

How estimates are calculated

Results are planning estimates: check them against manufacturer specifications.

Storage

  • Each group writes bitrate × cameras × recorded hours per day. Storage needed is daily footage × retention days, plus the reserve.
  • Real bitrate varies with the scene, night/IR noise and camera settings, so estimates are a range. For firm figures, choose Manual and enter the cameras' measured or configured bitrate.
  • Drives are sized for the high end of the range. RAID parity or mirroring and the reserve come out of raw capacity first.
  • Capacities are decimal TB, as on drive labels; recorders often show binary units, about 9% smaller.

Bitrate estimates are preliminary and not yet checked against measured cameras.

Open the Storage Calculator

Bandwidth

  • Camera traffic is bitrate × cameras for every group, plus the overhead allowance. Cameras stream all the time, so motion or schedule recording doesn't reduce it.
  • Remote viewing is viewers × cameras each × per-camera bitrate, plus overhead.
  • Real bitrate varies with the scene, night/IR noise and camera settings, so estimates are a range. For firm figures, choose Manual and enter the cameras' measured or configured bitrate.
  • Network checks use the high end of the range: OK up to 70%, Caution up to 90%, then “Above 90%”, and “Exceeds link” over 100%.

Bitrate estimates are preliminary and not yet checked against measured cameras.

Open the Bandwidth Calculator

PoE budget

  • Each device takes an allocation from the PoE budget: devices × allocation for every group.
  • Given as a PoE class: the class's full switch-side allocation, e.g. 15.4 W for class 3 and 30 W for class 4.
  • Given in watts: the datasheet maximum plus cable loss, solved at the port standard's minimum voltage (44 / 50 / 50 / 52 V), the same method behind the class allocations. A blank cable length assumes 328 ft (100 m).
  • The total load is OK within the budget less the reserve, a caution in the reserve, over above the full budget.
  • Four separate checks: power budget, PoE ports, port standard (the most one port can deliver) and cable length (328 ft (100 m), the Ethernet limit). The mobile bar and Export show the worst one.
Open the PoE Budget Calculator

Voltage drop

  • One cable per device. The drop is current × loop resistance, counting both conductors, out and back.
  • Copper at 20 °C. AWG from copper's resistivity; mm² from IEC 60228 class 5 maximums. Warm cable and copper-clad aluminium (CCA) drop more.
  • Loads in amps draw the same current at any voltage; loads in watts draw more as the voltage falls. A run that can't deliver the power is flagged.
  • 24 V AC is treated as DC at its RMS voltage. Transformers are rated in VA; current = VA ÷ voltage.
  • The smallest wire and longest run keep the drop within the limit. Within the limit doesn't confirm a device will run: check the voltage at the device against its minimum input voltage.
  • The supply load adds every device's current: OK within the rating less the reserve, a caution in the reserve, over above the full rating.
Open the Voltage Drop Calculator

Lens / FOV

  • The angle of view is 2 × atan(sensor size ÷ 2 × focal length); the width covered is distance × sensor width ÷ focal length. The lens is treated as distortion-free and aimed straight at a flat target; height and tilt aren't modelled. For wide-angle lenses, use the datasheet's field of view where given.
  • A sensor type such as 1/2.8" names its diagonal; the active area is that diagonal in the image's shape.
  • Pixel density is image width in pixels ÷ width covered (PPF or PPM). Resolution changes the density, not the field of view.
  • The pixel density levels are IEC 62676-4:2014's, listed in the calculator's Pixel density guidance. The 2025 edition revises them.

Real results also depend on lighting, focus, lens quality, compression, motion and camera angle: no pixel density guarantees that a person or face can be recognised or identified.

Open the Lens / FOV Calculator